NAME

Panotools::Script::Line::Image - Panotools input image

SYNOPSIS

A single input image is described by an 'i' line

DESCRIPTION

Basically the same format as an 'o' line.

 w1000
 h500     nona requires the width and height of input images wheras PTStitcher/mender don't

 f0           projection format,
                  0 - rectilinear (normal lenses)
                  1 - Panoramic (Scanning cameras like Noblex)
                  2 - Circular fisheye
                  3 - full-frame fisheye
                  4 - PSphere, equirectangular
 v82          horizontal field of view of image (required)
 y0           yaw angle (required)
 p43          pitch angle (required)
 r0           roll angle (required)
 a,b,c        lens correction coefficients (optional)
                  (see http://www.fh-furtwangen.de/~dersch/barrel/barrel.html)
 d,e          initial lens offset in pixels(defaults d0 e0, optional).
                  Used to correct for offset from center of image
                  d - horizontal offset,
                  e - vertical offset
 g,t          initial lens shear.  Use to remove slight misalignment
                  of the line scanner relative to the film transport
                  g - horizontal shear
                  t - vertical shear

 Eev          exposure of image in EV (exposure values)
 Er           white balance factor for red channel
 Eb           white balance factor for blue channel

 Ra           EMoR response model from the Computer Vision Lab at Columbia University
 Rb           This models the camera response curve
 Rc
 Rd
 Re

 Vm           vignetting correction mode (default 0):
                  0: no vignetting correction
                  1: radial vignetting correction (see j,k,l,o options)
                  2: flatfield vignetting correction (see p option)
                  4: proportional correction: i_new = i / corr.
                       This mode is recommended for use with linear data.
                       If the input data is gamma corrected, try adding g2.2
                       to the m line.

                      default is additive correction: i_new = i + corr

                    Both radial and flatfield correction can be combined with the
                     proportional correction by adding 4.
                 Examples: i1 - radial polynomial correction by addition.
                                 The coefficients j,k,l,o must be specified.
                           i5 - radial polynomial correction by division.
                                 The coefficients j,k,l,o must be specified.
                           i6 - flatfield correction by division.
                                 The flatfield image should be specified with the p option

 Va,Vb,Vc,Vd  vignetting correction coefficients. (defaults: 0,0,0,0)
               ( 0, 2, 4, 6 order polynomial coefficients):
                corr = ( i + j*r^2 + k*r^4 + l*r^6), where r is the distance from the image center
              The corrected pixel value is calculated with: i_new = i_old + corr
              if additive correction is used (default)
			   for proportional correction (h5): i_new = i_old / corr;

 Vx,Vy        radial vignetting correction offset in pixels (defaults q0 w0, optional).
                 Used to correct for offset from center of image
                  Vx - horizontal offset
                  Vy - vertical offset

 S100,600,100,800   Selection(l,r,t,b), Only pixels inside the rectangle will be used for conversion.
                       Original image size is used for all image parameters
                       (e.g. field-of-view) refer to the original image.
                       Selection can be outside image dimension.
                       The selection will be circular for circular fisheye images, and
                       rectangular for all other projection formats

 nName        file name of the input image.

 i f2 r0   p0    y0     v183    a0 b-0.1 c0  S100,600,100,800 n"photo1.jpg"
 i f2 r0   p0    y180   v183    a0 b-0.1 c0  S100,600,100,800 n"photo1.jpg"

Rotate transform the image, angles in degrees:

$i->Transform ($roll, $pitch, $yaw);